Version 3.6.6 - 03.21.2025
- Added the option to specify a separate front and back gable overhang length for all truss types.
- Augmented the web generation algorithm for coffer trusses with deep coffer ceilings.

I haven't revisited this image in a few years but I still need to put together a complex porch roof module:



Time to put the old thinking cap back on.

As I look at this image from about 8 years ago, when I was just starting the Truss plugin, two things immediately jump out at me. Everything can be quickly modeled now except for:

1.) The porch rafter roof (complex shed roof with hipped ends)
2.) The opening in the floor for the stairwell

Obviously my work is not yet complete.

Version 3.6.5 - 03.16.2025
- Added energy/raised heels for coffer trusses (3 variants: wedge, slider and vertical w/ strut).
- Enabled a feature to selectively remove specific trusses from coffer truss assemblies.

Version 3.9.2 - 03.15.2025
- Enabled an edge material/texture for built-in gypsum wall materials.

Version 3.6.4b - 03.15.2025
- Enabled subtractive geometry for all TJI and Glulam Beam rafter roofs.

Version 3.6.4 - 03.13.2025
- Enabled subtractive geometry for all dutch gable rafter roofs.

Version 1.2.5 - 02.28.2025
- Fixed a critical bug with the estimating module (wall sheathing 2).

Version 3.9.1 - 02.23.2025
- Added the following (48 - low poly) Simpson post caps to the post module: CC1210, CC718_718, CC718_8, CC718_6, CC718_4, CC514_8, CC514_6, CC514_4, CC462_550, CC462_462, CC462_362, CC314_6, CC314_4, CC128, CC126, CC106, CC98, CC96, CC94, CC88, CC86, CC84, CC78, CC77, CC76, CC74, CC68, CC66, CC64, CC48, CC46, CC44, CC6_718, CCO4, CCO6, CCO7, CCO8, CCO9, CCO10, CCO12, CCO46, CCO314, CCO462, CCO514, CCO718, ECC64, ECC66, ECC68.





This update per customer request.

I still need to add in the rest of the ECC series, so there is always more to do.

**Version 1.5.0** - 02.16.2025
- Added two generic side discharge hvac/heat pump condensor units into the built-in library: HP_XV19_42, HP_XV19_36.
- Added various "Wilkerson Art" framed art prints within the "art" category under misc. fixtures: Wasco, Frog, Hummingbird, Eagle under Sun, Killer Whale, Abstract and Medeek (Grizzly Bear).





http://www.wilkersonart.com

The funny thing is that I added the hummingbird framed art back in June (2024) as an Easter Egg but I guess no one noticed, or at least no one ever messaged me about it so I guess it went undetected.  I've also added in a decent wall clock as well for those needing a wall clock mounted in a room.

Decided to take a much needed break from the code today and did some other misc. tasks.  This one just kind of popped up on my radar so I figured I would add a few more framed prints.

As far as using the artwork in any of your projects, so long as you hold a licensed copy of the Medeek Electrical plugin you are authorized to use my artwork in any personal or professional projects you see fit.  My only request is that if you do decide to use the artwork, please give attribution where possible and applicable.

I've started working on adding in a scissor truss option into the module. Here are some quick and dirty (sorry I must have set my lunch down on my engineering pad earlier today) calcs for the heel joint of such a truss:

Version 3.9.0d - 02.14.2025
- Fixed a floating point rounding bug for metric templates.
- Fixed a bug for balusters when a run of stairs is a single step.

Still putting out a few little fires.  Whenever you make big changes it always seems like you miss something or you add a new feature that adds a whole new level of complexity, and then the plugin gets itself into states that you did not foresee.  That is what makes this job fun, you get surprised once in a while.

Please feel free to send me any additional bug reports or feature requests.  I think we've just about wrapped up the stair module for a while.

Version 3.9.0c - 02.12.2025
- Fixed a bug when the top tread is flush.

Version 1.4.9 - 02.11.2025
- Added three generic hvac condensor units/sizes into the built-in library (with WeatherGuardTM tops): 30X28_WG, 30x32_WG, 30x40_WG.



These additional variants added per customer request.  They are the exact same as the similar sized units other than the addition of the weather guard top.  Hopefully this gives enough selection for typical residential AC units however if there is need for any other styles etc... please let me know.

Version 3.9.0 - 02.11.2025
- Enabled zero size intermediate posts (balusters) for glass railing.
- Fixed a bug with floor level winders/landings for landing treads and covers.

Version 3.8.9 - 02.09.2025
- Added preview thumbnails for handrail fittings to the draw and edit menus of the stair tool.
- Fixed a bug with adjacent winders/landings for landing treads and covers.
- Fixed a minor bug with materials for handrail fittings.