News:

SMF - Just Installed!

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - Medeek

#16
Version 3.8.7 - 01.28.2025
- Enabed subtractive geometry for all stair assemblies.
- Added the following two parameters to the baluster sub-menus: Baluster Type (Square, Round, Glass, Cable), Baluster Height.
- Enabled intermediate posts for both glass and cable railing.
- Added the following cable railing options into the Stairs tab of the Global Settings: Cable Railing Spacing, Cable Railing Diameter.
- Added a bottom vertical offset parameter for bottom posts of a stair run.





Tutorial 65 - Cable and Glass Railing (13:26 min.)

#17
Tutorial 64 - Modern Stairs (12:43 min.)

#18
Version 3.8.6 - 01.25.2025
- Added tread covers, carpet and stair runners for T-shaped landings.
- Enabled the option for a single stringer (for modern style stairs).
- Added an option to disable the placeholder for landing/winder framing.
- Added a "GLASS" option for balusters within the built-in baluster materials.
- Added a "None" built-in option for the handrail profile parameter.





#19
Tutorial 63 - Stair Runners and Tread Covers (10:06 min.)

#20
Version 3.8.5 - 01.21.2025
- Updated the skirt boards to accommodate open treads.
- Added tread covers, carpet and stair runners for stairs, landings and winders.

#21
Also an FYI.  I'm testing out Discord (Medeek Channel) for those who want to chat more interactively.  I can't guarantee I will be on all the time so this is a bit experimental:

https://discord.gg/hq5fxEEG
#22
Version 3.8.4 - 01.14.2025

- Added a minimum winder depth parameter for all stair winder types.
- Adjusted the deck handrail algorithm for narrow cap rails (2x4).

#23
Version 3.8.3 - 01.10.2025
- Added a "deck" profile or option for handrails (with balusters) to the stair module.

Tutorial 61- Handrails for Decks (8:51 min.)

#24
First look at handrail and post options for "deck" staircases:



I have some more work to do on the balusters or pickets but I should have this wrapped up by tomorrow and then back over to the Floor plugin.

The top run of stairs is set to the "Vertical" or post-to-post option, whereas the bottom run is set to "OTP". I've seen both variants when it comes to typical deck staircases. If there are others I can also add them in but I will start with these two for now.
#25
Version 3.8.2 - 01.05.2025
- Added balusters to the stair module for vertical and OTP handrails.
- Added newel posts to the stair module for vertical and OTP handrails.

Tutorial 60 - Balusters, Posts and Handrails (16:39)

#26
First look at over-the-post handrails with posts:



#27
Tutorial 59 - Multi-Board Treads and Side Spacers (7:15 min.)

#28
Version 3.8.1 - 01.02.2025
- Added additional sizes to the post module for steel square tubes.
- Updated the side spacer algorithm for stairs.
- Enabled wood grain texture for treads, risers, thrust blocks and stringers.
- Enabled a multi-board tread and spacing parameter for stairs.
#29
Tutorial 58 - Open Treads and Starter Steps (7:35 min.)

#30
Medeek Floor Plugin / Re: Suggestions, Ideas and Roadmap
December 30, 2024, 11:02:17 PM
I will give this some consideration.  I have been working on the stair module for a couple weeks but I will get back to the Floor plugin after the new year and be working on MPC trusses and the opening tool then address any other items on the todo list.