Recent Posts

Pages: [1] 2 3 ... 10
1
Medeek Truss Plugin / Re: Development and Updates for the Medeek Truss Plugin
« Last post by Medeek on December 13, 2017, 12:19:05 am »
The license registration module was causing some problems in isolated cases so I've released a sub-rev. 2.1.1b to address that issue.

If you are trying to enter in your serial number and it does not appear to take, first verify that you are not entering in any leading or trailing white spaces if that does not solve the problem you may be encountering the issue at top, in that case download the latest version which should address the issue fully.
2
Medeek Truss Plugin / Re: Development and Updates for the Medeek Truss Plugin
« Last post by Medeek on December 11, 2017, 05:48:31 am »
Featured on the SketchUp Extension Inspection:

3
Medeek Truss Plugin / Re: Development and Updates for the Medeek Truss Plugin
« Last post by Medeek on December 10, 2017, 01:40:55 am »
I am working on adding the heel blocking since it is an option listed in the advanced options.



So far there has not been much call for this feature but a few people have inquired so I figured we might as well add it in for completeness.  The red coloration is for clarity in the image above.

I will probably add the option to allow for venting holes since this is fairly typical in my neck of the woods.
4
Medeek Truss Plugin / Re: Development and Updates for the Medeek Truss Plugin
« Last post by Medeek on December 03, 2017, 01:37:31 pm »
As the number of advanced options have increased (common trusses) the user input menu has slowly grown in size until it is so large that it often does not fit the screen of many laptops and smaller screens.

This problem has been well documented by a number of users for quite some time.

This weekend I spent some time putting together a new HTML menu for advanced options for roof trusses:



I still need to work out the metric version and also all of the language translations but otherwise I think it is almost ready to roll out.

As you mouse over each of the options a 320x240 image will display as shown, hopefully clarifying the meaning or usage of each parameter/option.
5
Medeek Truss Plugin / Re: Development and Updates for the Medeek Truss Plugin
« Last post by Medeek on November 29, 2017, 03:29:21 am »
The reason I am taking so long with complex rafter and truss roofs is the possible permutations is making things very challenging.

For example take the truss roof below:



I'm assuming there are no interior bearing walls and we want to clearspan the entire building outline.  I can get the basic roof and truss layout by creating to hip truss sets as primitives but that is where it then becomes very interesting.

As you can see there are two mid-building girder trusses that then catch the mono pitch sub-girders which are each supporting two common trusses.  Next to the sub-girders is a small valley set (half valley) that fills in the roof behind the sub-girders. 

The largest span is 36', which is reasonable.  This appears to be the simplest way to truss this roof out but is probably not the only solution.  A good truss technician could tell me how close I am to the optimal solution.

Granted the complex rafter roof is not IMHO as hard a problem but it also has similar difficulties and issues. 

View model at this link:

https://3dwarehouse.sketchup.com/model/24c19aa6-814a-4e9e-aa42-a0e0de1ba74c/Complex-Truss-Roof-8
6
Medeek Truss Plugin / Re: Development and Updates for the Medeek Truss Plugin
« Last post by Medeek on November 28, 2017, 12:51:39 pm »
Version 2.1.0 - 11.28.2017
- Added Northeast hip set trusses.
- Enabled advanced options for northeast hip sets.
- Added energy/raised heels for northeast hip set (3 variants: wedge, slider and vertical w/ strut).
- Added the option for open vs. closed end jacks.
- Added the option for a drop in purlin frame.
- Enabled a graphical user interface for Truss Set selection.





I only plan on adding the midwest and california variants if requested.
7
Parameters for the door jamb detail:

8
I'm not sure how far I will take this plugin, I was only intending to create a very simple plugin to integrate with the Wall and Truss plugins however I can see already that there is a need for a very robust and full featured window and door plugin.

The plugin logo will be: 



The tool bar thus far:

9
Doors get a bit more complicated. The placement of the door jamb within the rough opening depends on the sheathing thickness on both sides of the wall, or in more precise terms the jamb depth depends on the wall framing thickness (2x4, 2x6, 2x8 etc...), the sheathing thickness (OSB, Plywood, etc...) and the interior gypsum thickness. With an interior door the sheathing is usually gypsum on both sides of the wall.

A typical door jamb thickness is 3/4" with a 1/4" RO gap for shimming and squaring the door up on each side and at the top. The nominal door size is the door opening width from jamb to jamb not the actual door itself. The door width will be 3/16" of an inch less than the door opening width or nomimal size assuming a 3/32" reveal or gap for the door.

With an 1/8" gap between the top of the door and the jamb this leaves 7/8" between the sub floor and the bottom of the door assuming the RO height is 2" greater than the nominal door height.

For some exterior doors a taller threshold may be required so a RO height that is 2.25" to 2.5" greater than the nominal door height may be required.

Please weigh in if I am missing something here.

I'm am focusing specifically on standard prehung doors, sliding glass doors are a slightly different animal.

For a typical door there could be a whole host of parameters, I am thinking an html GUI would be the best with an SVG preview screen showing the door in elevation and a section detail for the jamb, threshold and header.

The door location and size would be determined by picking three points similar to the window so that any size of door could be specified for a given rough opening.
10
I know there are a lot of plugins out there that do this well and I am not really interested in competing against them.

I just want a simple door and window plugin that I can integrate tightly with my other plugins.

The window module will have the following options (subject to change):

1. Window Type: Picture, Slider, Single Hung
2. Frame Color
3. Frame Width
4. Frame Depth
5. Glass Thickness
6. Sash Width
7. Sash Depth
8. RO Gap
9. Window Inset
10. Nail Fin: Yes/No
11. Nail Fin Length
12 Advanced Options: Yes/No

The global settings will allow the user to set up the defaults for all of these settings and others. The window location and size will be selected via three points with a preview vector showing the exterior facing direction in some sort of fashion.

I haven't thought through all of the advanced options yet but mullions will probably be one as well as other embellishments.
Pages: [1] 2 3 ... 10