First look at a polygon floor using MPC floor trusses.



However the following the items still need attention:

Gable trusses
Ribbon boards
Multiple chase locations

Version 1.5.2 - 06.02.2025
- Updated the wire library to include all the common NMB wire sizes.





This update per customer request.

Wire sizes per the Southwire (Romex) documentation:

http://design.medeek.com/resources/electricalplugin/references/2403_3-C_Romex_NMB_Cable_SpecSheet_Web.pdf

Version 4.0.2 - 06.01.2025
- Added a bottom gap parameter to the draw and edit menu of the door module.
- Added the bottom gap parameter to the door tab of the global settings.

Tutorial 26 - Editing Opening Headers (5:00 min.)

Version 1.0.6 - 05.31.2025
- Added an edit function to the "Stretch Floor Header" tool.
- Added a "Timber" header type for floor openings.
- Fixed minor bugs in the floor opening module.

Version 1.0.5 - 05.30.2025
- Added the ability to stretch opening headers with the "Stretch Floor Header" tool.

Tutorial 25 - Stretching Opening Headers (7:50 min.)

Here is a quick mock up of a window wall in SketchUp (circa. 2016). This is before I had the wall and foundation extensions completed, however the roof was actually drawn using the Medeek Truss plugin (that did save me some time). This model helped visualize what was going on with this specific design and also helped me quickly realize that there were some areas that needed special attention.



The room below the window wall was actually just a rather tall crawl space but note how the load path of the in-wall columns extend down through the crawl space wall and then the resulting spread footings below them. The columns are supporting the roof glulam beams and as a result are relatively loaded.

Notice the rear wall and how many openings it has, a bit tough to make this design actually work (shear). I also ran into my first real encounter with interior shear walls. With interior shear walls it is important that they extend up into the attic space and complete the load path with the roof diaphragm.



I've also attached a related shearwall fix where the contractor did not initially include a double sill plate. Physical, on-site inspections of the framing were always a requirement, a lot of the times there were quality or other issues that needed addressing. Or in some cases the contractor did not fully understand the intent or requirements of the structural plans.

Before I ever ventured into the plugin development world I did quite a bit of residential structural work. Since then I've pretty much switched hats and now my entire focus is on the extension development.

As a resource to other designers, architects and engineers I may occasionally post a few examples of structural work I've done over the years. Most of this work was done about 10 years ago. Note that I've removed any private or identifying information. Additionally these examples are for Educational Purposes ONLY and are not intended as a specific engineering solution for any other project or plan. Let me know if any of this is helpful or useful and I might be inclined to post a few more examples.

Here is a simple braced wall plan detail:

Version 4.0.1 - 05.29.2025
- Added five additional layers to the Layers tab of the Global Settings for stair assemblies.
- Added a "Stair Layers" option into the Layers tab of the Global Settings in order to toggle the stair layers "On" or "Off".

Tutorial 71 - Layers/Tags for Stairs (4:02 min.)

Version 4.0.0b - 05.28.2025
- Enabled "green" pressure treated lumber within the stair module.

Version 1.0.4 - 05.26.2025
- Enabled joist hangers for openings.



Tutorial 24 - Joist Hangers and Openings (7:58 min.)

Version 1.0.3 - 05.25.2025
- Enabled I-Joist floor headers for openings.

Tutorial 23 - Joist Removal (8:06 min.)

Version 1.0.2b - 05.23.2025
-Updated the joist removal function for more granular usage when working with staggered joists.

I apologize for all of these micro updates, I would have preferred to roll this out after adding a few more features etc... However, the user who requested this specific ability obviously needs it to complete their project so it is simply a matter of expediency.



Now one can not only specify a single line of joists to remove but also remove specific joists from a given line, see screenshot above and note the syntax in the Remove Joists field.