News:

SMF - Just Installed!

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - Medeek

#601
Version 1.8.8 - 02.17.2021
- Enabled options for wood grain texture for lumber and pressure treated lumber in the global settings.



#602
Comparison between the solid coloring and with the textures enabled (Lumber and PT Lumber):



I am quite happy with the way the pressure treated texture came out.
#603
I've had a number of people recently ask me for the ability to apply a wood grain texture to the lumber (ie. studs, plates, blocking, etc...)  This really isn't a big ask, so I am going to enable another couple parameters in the global settings (Material Tab) so that the user can apply a texture to lumber and pressure treated lumber.  Here is a first look at what that will look like (compare the wood grain wall to the solid colored wall):



I've tried to be very subtle with the wood grain texture so that it approximates my default lumber color but as you can see it is a slightly darker shade.  I'm not sure I am entirely happy with it yet but it is a start.
#604
Medeek Wall Plugin / Re: Using 2D in Scenes
February 16, 2021, 11:10:43 AM
Don't change all of your walls to 2D, leave them as 3D and in the global settings (General Tab), turn on the "2D Geometry in 3D".  This will allow you to have both and then in your scenes you can show whichever is necessary.
#605
Version 1.8.7 - 02.15.2021
- Added an option for the garage door track in the global settings.



Currently you cannot set this parameter per garage door, it can only be set globally (in the Garage Door tab).

#606
Version 1.2.7b - 02.13.2021
- Enabled the ability to draw UK outlets and switches with Medeek Polyline Stemwall assemblies.

#607
Version 1.2.7 - 02.13.2021
- Enabled the ability to draw outlets and switches with Medeek Polyline Stemwall assemblies.

#608
Version 1.6.6 - 02.12.2021
- Added logic to the final assembly routine to allow for electrical components (Medeek Electrical) to be retained within all foundation assemblies.

#609
Version 1.8.6 - 02.11.2021
- Added the following Simpson Strong-Tie hangers to the beam hanger library: LUS26-2Z, LUS28-2Z, LUS210-2Z.
#610
Version 2.8.0 - 02.10.2020
- Minor modification to the range of available pitches for valley truss sets.
#611
Version 1.6.5 - 02.09.2021
- Fixed a bug with anchor bolt placement for polyline stemwalls.
- Added an option for a zero depth footing for polyline stemwalls, which eliminates the footing for this foundation type.



By setting the depth of the footing to zero you can eliminate the footing from a polyline stemwall, so only the stemwall portion of the foundation is drawn.  This is per customer request.

Also the algorithm for anchor bolt placement for polyline stemwalls is greatly improved, however there can always be further improvements, any feedback is always appreciated.
#612
When the foundation segment lengths in a polyline stemwall foundation are too short this is what you get (notice the anchor bolt placement):



I'm working up some additional logic to properly deal with anchor bolt placement with short segment lengths.
#613
Version 1.8.5b - 02.08.2021
- Fixed a bug with the top plate cut out algorithm when walls meet in a "cross" configuration.



Each wall teeing into the primary wall has had its corner offset set to 1/2 the thickness of the primary wall.
#614
I think the new Copy Wall tool will prove to be quite useful.  As I am thinking about it this morning I realized that a similar tool for Doors and Windows would also be quite useful. 
#615
Version 1.8.5 - 02.07.2021
- Enabled the "Wall Copy" tool within the Medeek Wall Tools toolbar.



Note I've only enabled this tool for rectangular walls.  After I am fully confident that it is working well and I've addressed any bugs or issues I will set it up for all the other (gable,shed and hip) wall types.

Please try out this new tool and provide any feedback or comments directly to nathan@medeek.com