News:

SMF - Just Installed!

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - Medeek

#1441
First look at the output of the Light Fixture Module:







The plugin allows you to drop your own light fixtures into the library sub-folder so you can have as many custom light fixtures as you like (and I don't need to spend anymore time modeling things up).

The fancy ext. wall lantern shown was simply downloaded from the warehouse, minor edit to make sure the origin of the file was in the correct place and then dropped into the light_fixture sub-folder.  I will not be including this fixture in the distribution simply due to its size (1.2 Mb).  However I will include some basic lampholders like the Leviton 49875 shown.

Another thing to note, since the light fixtures are custom I will not be attempting to apply any material or color to them.  For that reason there is no need to explode the component into a unique group. 

I will add some additional simple light fixtures and junction boxes as time allows or as requests are made.

Currently the light fixture tool is limited to wall mounted fixtures.  I am still contemplating how best to deal with ceiling mounted fixtures and what type of system/organization to employ.
#1442
Electrical boxes for light fixtures:

https://3dwarehouse.sketchup.com/model/28673308-2a85-43ad-90f9-1f4f82231bf6/Electrical-Boxes

I'll start with the simple nail mounted 3/0 and 4/0 boxes (Carlon B518 and B520).  I should also add the hanger bar variants as well but I'll need to purchase a few more samples from the local hardware store first so that I can create semi-decent models.
#1443
Just a reminder to everyone that is following the development of this plugin:

This plugin is an add-on plugin/extension.  In other words it currently only installs switches, outlets, low voltage outlets and panels into the walls that are created by the Medeek Wall extension.

At some point I may attempt to extend it to allow for operation with any solid walls but for now it is limited to working with the geometry created by the mdkBIM suite.  There are a number of technical issues/reasons for this which I will not delve into at this time.

Since it is not a stand alone plugin and is dependent (currently only on the Medeek Wall extension) I will probably not charge as much for it if it were a standalone extension.  As such I am thinking about $20.00 USD for a permanent license with a $10.00 USD renewal for upgrades.

Eventually it will be packaged with the mdkMEP suite but for now it is a standalone purchase and separate from the mdkBIM suite.

It will eventually include its own estimating module which again is separate from the Medeek Estimator (Wall Plugin).  I really haven't gotten that far yet but I will solicit feedback from the user base of this plugin once I release the BETA and determine how we want to put that together.
#1444
Perusing the selection of electrical outlets and boxes at my local Ace Hardware this morning it became painfully obvious that I should have added the option for "amperage" to the outlet parameters.

Standard and Decora outlets now are available in 15A or 20A:



I've never actually seen this type of outlet (NEMA 5-20R) installed in any residence I've ever lived at or in any new construction I've worked on but I'm sure it has its place.

Currently the 240V outlets are limited to only 30A and 50A outlets.  At some point I may add in NEMA 6-15R and NEMA 6-20R if there is call for it.
#1445
Version 1.0.3 - 02.11.2019
- Fixed a bug in the display of the toolbars (Mac and Windows).
- Added a trimmer extend option to extend trimmers up to bottom of header when a built-up header is used that has a bottom plate.



In certain jurisdictions the trimmers (jack studs) must extend to the bottom of the actual header and not to just the bottom plate of the built-up header.  This option allows one to set this per window and also within the global settings.

The toolbar bug is probably more apparent to Mac users but technically also affects Windows users as well.
#1446
First look a the output of the load center or service panel module:

#1447
In the parameters for the load centers I identified the following options:

1.)  Style:  Flush Mount, Surface Mount
2.)  Indoor/Outdoor:  Indoor, Outdoor
3.)  Height:  Distance from floor to bottom of box (in./mm)
4.)  Breaker No.:  6, 8, 12, 24, 30, 40, 42, 54, 60
5.)  Amperage:  100, 200
6.)  Main Lug:  Main Breaker, Main Lug
7.)  Adv. Options:  None Currently

There is no material/color assignment. 

I've created a 6 and 8 breaker box (main lugs only).  I will need to add in additional boxes that only have main lugs and not a main breaker for the other sizes, but that is work for another day.
#1448
The inside of these boxes and the breakers are very simple and low poly.  The idea is mostly to convey the number and location of breakers and overall dimensions:

#1449
Various load center sizes, view model here:

https://3dwarehouse.sketchup.com/model/d1271b9e-fa3f-4c74-beba-750d5d330ff0/Load-Centers-Low-Poly

All load centers are 200 Amp except for the 24 space unit which would be rated for 100 or 125 Amp.
#1450
Tomorrow I will finish modeling up some typical load centers (breaker boxes) like the one below (200 Amp, 40 Spaces):



I'm not going to put any special logic into this module yet, just a simply positioning and selection.  However at some point it would be really cool to use the plugin to setup the various breakers and identify circuits as well as assign specific elements to a circuit.

For now three sizes of breaker components are provided and it is up to the user to manually configure their panel if they so choose to do so, otherwise is is more representational than anything else.

When it comes to setting the vertical height of the load center what is the method used to measure from the floor?  Center, Top or Bottom of the panel?

I will provide some common panel sizes (spaces):  24, 30, 40, 42, 54, and 60.

My breakers are based on the SquareD QO series as are my load centers however they are considerably simplified to maintain a low poly count.

Also for now I am only going to provide flush mount and not surface mount however I will probably enable both in the future.

View model here:

https://3dwarehouse.sketchup.com/model/560f7404-63e8-4b7f-9920-eb0775ae5e34/Load-Center-Example
#1451
Various combinations of QuickPorts yields a number of possible 2D symbols:



I've tried to stay with conventional symbols as much as possible.  Please let me know what you think on this.
#1452
The low voltage module is working pretty good now.  I just need to wrap up the 2D symbols and then we will see if I can put together a few typical load centers, and then its out to the public for some BETA testing.

A 2-gang, 12 port low voltage box is probably your worst case scenario:



Each port can be assigned one of the following:

- CAT6
- CAT5e
- COAX
- PHONE (RJ11)
- RCA (Audio/Video, gold plated)
- BLANK (Plastic Insert)

Additionally each port has its own unique material/color which by default is "White".  The faceplate can also be assigned a unique material/color.

Similar to other outlets the advanced options can be enabled which allows for vertical or horizontal mounting.

The number of possible QuickPorts is limited to the following:

1-Gang:  1, 2, 3, 4, 6
2-Gang:  8, 12

There are additional 2-Gang QuickPort wall plates that I have not added.  I will only add these if requested, since they are already covered by the 1-Gang option.
#1453
The updated toolbar:



I will leave it up to inquiring minds to figure out what all these icons mean. :)
#1454
Just loaded the Wall Plugin into SU 2019 and so far all is good. I did notice that the HTML menus seem to be loading quite a bit faster and the performance overall seems to have improved. It looks like the browser engine under the hood has been updated and already there is a marked improvement, thank-you SketchUp.

When you drag a menu and then select a drop down box the bug where the drop down opens up at the previous location is now resolved. Looks like I might have to update to SU 2019.
#1455

I've also added in the RCA QuickPort by request.



You will be able to assign a unique QuickPort outlet to each port of the wall plate and also assign it its own unique color if you choose (this will be important for people who are color coding network jacks).