News:

SMF - Just Installed!

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - Medeek

#856
Version 1.4.0b - 05.01.2020
- Fixed a critical bug with the tee intersection ladder blocking with walls with no openings.
- Added a "Rustic Shiplap" built-in material into the material library.



#857
Version 1.4.0 - 05.01.2020
- Enabled a second layer of gypsum for interior and exterior walls.



This update adds an optional 2nd layer of gypsum to the wall assembly.  By disabling the first layer of gypsum one can create an air gap between the 2nd layer of gypsum and the framed wall.

This update also addresses a minor bug caused by the updates in Version 1.3.8.

This latest update will require the user to recreate their wall presets since three new parameters have been added to the wall attribute library.

View an example of double gypsum walls here:

https://3dwarehouse.sketchup.com/model/fca7d773-6c68-4b86-b51e-68492cef6ce4/Double-Gypsum-Walls
#858
Version 1.3.9 - 04.28.2020
- Added a "Terminal" end wall condition.



The principal use of this end condition is for interior walls terminating against multi-wall corners as shown above.
#859
Version 1.1.5 - 04.28.2020
- Added a Global Reset button in the General tab of the Global Settings.
- Plugin files switched from .rbs to .rbe encryption.
#860
Version 1.5.8 - 04.27.2020
- Added a Global Reset button in the General tab of the Global Settings.
- Plugin files switched from .rbs to .rbe encryption.

#861
Version 2.7.3 - 04.26.2020
- Added a Global Reset button in the General tab of the Global Settings.

#862
Version 1.3.8 - 04.26.2020
- Added additional logic to the blocking and insulation modules for short wall panels.

#863
Version 1.3.7b - 04.25.2020
- Added a Global Reset button in the General tab of the Global Settings.



No more messing around with registry entries, plist files and JSON files.  Just click the button and you start with a clean slate, why didn't I think of this before.
#864
Version 1.3.7 - 04.25.2020
- Fixed the HTML tabs of the global settings (page 2).
#865
After some further analysis it would seem that I need one additional "end" wall condition, see image below:



In this situation you have multiple walls coming together at a single location.  The exterior walls constitute an inside corner however the interior wall is not a normal "tee" intersection.  If one uses the "end" condition then the end of the interior wall is wrapped with gypsum as shown and the gypsum on the exterior wall is not removed.  It you try to use a "tee" condition the interior wall top plate wants to remove part of the exterior wall's top plate, so this doesn't really work either.

I am going to call this wall condition a "terminal" wall condition.  Essentially it is identical in behavior to the "end" wall condition however it does not get a gypsum wrap (interior walls), but it will also still remove any gypsum/sheathing/cladding of any wall it terminates against.

See model here:

https://3dwarehouse.sketchup.com/model/0ab6f9a1-e1ff-43c2-bcff-96db69cb1438/Terminal-Wall-Condition
#866
Version 2.7.2b - 04.24.2020
- Enabled the "Edit Truss Assembly" function for all tail bearing trusses (imperial and metric units).
- Labels and callouts added to tail bearing trusses.





This update also resolves a potential bug that could cause the plugin to go into a infinite loop if the birdsmouth cut exceeds the depth of the top chord of the truss.  If you are using tail bearing trusses I highly recommend upgrading to this latest release.

The updated module is now properly creating the gypsum on the underside of the truss (three pieces).
#867
Version 2.7.2 - 04.24.2020
- Added wall sheathing thickness and wall cladding thickness parameters to the advanced options for trusses.
- Enabled advanced options for tail bearing trusses.



I still need to enable editing and labels for tail bearing trusses.
#868
Version 1.3.6 - 04.22.2020
- Resolved an issue with UTF-8 encoding.
#869
First look at the Skylights Toolbar:

#870
Velux has their official models in the warehouse but as usual there are too many details in these models, so I had to create my own low poly versions that are dimensionally accurate:



https://3dwarehouse.sketchup.com/model/f56a0a28-e161-46ce-a051-ea081c9e2a74/Medeek-Skylights-Velux-Low-Poly